San Antonio Gate Pros provides professional welding & gate fabrication in San Antonio, TX for residential and commercial properties across the San Antonio area. We run our own metal shop, which on a rock market matters more than it sounds. Half the foundation solutions we use need a part made for the situation the drill found, and a contractor who only installs catalog parts designs around what is in the warehouse.
Baseplates are the clearest example. When a test hole hits solid limestone eighteen inches down, the right answer is often not a deeper hole but a fabricated plate sized to that specific post, drilled for the anchor pattern the rock will accept, welded up and galvanized. That is a shop job, and having the shop means we can quote it the same day instead of turning a good foundation into a special order.
The same applies to post assemblies, cantilever truck brackets, gusseted hinge boxes, pedestal mounts and adapters for operators that were never designed to bolt to stone. We cut, weld and coat to drawings rather than assembling from kit parts, and everything we build gets blasted, pretreated, hot-dip galvanized where the exposure calls for it, and powder coated in house. Adapters are a large part of what the shop actually makes.
Repair work is the other half of the shop. Ranch pipe gates bent by livestock or equipment, iron leaves damaged by vehicles, rusted bottom rails spliced out and replaced, cracked welds rebuilt, wood gates given the steel frame they should have had, and handrails, security screens and one-off brackets made to fit. Most of it happens on site with the mobile rig. Most of it is one visit and no second trip.
Fabricating what we install also means a repair years later comes back to the people who welded it. We keep the drawings and the powder batch on record, so a matched section can be built without anybody guessing at a profile or a color. Color matching from a record beats matching from memory, and it is the difference between a repair you cannot find and one you notice every time you drive in.
Galvanizing has a schedule and it governs the job, which surprises people. A hot-dip batch is a trip to the kettle and back, usually a week or more, and nothing can be welded after it without burning the coating off. So every hole, every bracket and every anchor point has to be settled before the steel goes out. We drill for anchors already confirmed against the test holes rather than guessing.
If you are unsure whether something should be repaired or replaced, ask us. We will tell you when a frame is too far gone to weld into honestly, and we will also tell you when the replacement quote you are holding is solving a two-hour problem. Second opinions are free and we give a lot of them on gates other people built. If replacement genuinely is the answer, we will say that plainly.
With 15+ years of experience, our insured team brings the right materials and equipment to every job — wrought iron and ornamental steel fabrication, ranch entry gates and pipe fencing, truck-rated cantilever slide gates, LiftMaster, DoorKing and FAAC operators, Class I-IV operator classifications, UL 325 entrapment protection — and backs the work with a written workmanship warranty. We serve San Antonio and nearby communities including Alamo Heights, Schertz, Converse, Universal City.
What We Handle
Everything our welding & gate fabrication in San Antonio covers
One crew, one point of contact, and the full range of welding & gate fabrication work in San Antonio, TX. If it is on this list we do it in house rather than handing it to a subcontractor:
- custom gate fabrication
- on-site mobile welding
- structural gate repair
- gate frame re-welding
- metal fabrication shop
- post and hinge welding
- gate bracket and hardware fabrication
- railing and gate welding
- cracked weld repair
- handrail and guardrail welding
- gusset and bracing repair
Not sure which one describes your situation? Describe it in plain words and we will sort it out — or browse the rest of our San Antonio services.
Materials, equipment and how we do welding & gate fabrication
The difference between welding & gate fabrication that lasts and welding & gate fabrication that gets redone in three years is almost always preparation and materials, not the finish you see on day one. We work with wrought iron and ornamental steel fabrication, ranch entry gates and pipe fencing, truck-rated cantilever slide gates, LiftMaster, DoorKing and FAAC operators, spec them to the job instead of to the invoice, and write the material grades into the free estimate so you know exactly what you are buying.
Every San Antonio job runs the same way: site walk and measurements, written scope and fixed price, protection of the surrounding area, then the work itself with a daily clean-up. 15+ years of gate work in the San Antonio area means we have already met whatever your property is going to throw at us — awkward access, older construction, an HOA with opinions.
Where we do welding & gate fabrication outside San Antonio
San Antonio Gate Pros covers San Antonio and the surrounding communities of the San Antonio area. Crews run out to the same nearby cities every week, so an out-of-town job does not mean an out-of-town price.
- Welding & Gate Fabrication in Alamo Heights, TX — Bexar County, population 8,400
- Welding & Gate Fabrication in Schertz, TX — Guadalupe, Comal and Bexar Counties, population 45,000
- Welding & Gate Fabrication in Converse, TX — Bexar County, population 28,000
- Welding & Gate Fabrication in Universal City, TX — Bexar County, population 20,000
- Welding & Gate Fabrication in Boerne, TX — Kendall County, population 20,000
- Welding & Gate Fabrication in Helotes, TX — Bexar County, population 10,000
Start on the San Antonio Gate Pros homepage for a free estimate, or call (877) 583-3964 and describe the job.
Why San Antonio Chooses San Antonio Gate Pros
- ✓Over 15 years installing and servicing gates across Bexar County and the Hill Country
- ✓In-house metal shop — we weld and powder coat our own gates rather than reselling panels
- ✓Footings sized to your actual soil, clay on the south side or limestone north of 1604
- ✓Every operator wired to UL 325 with photo eyes, loop detectors and tested entrapment protection
The standards behind welding & gate fabrication
Quality here is not a matter of opinion — it is written down. The welding & gate fabrication work we do in San Antonio follows published industry standards: DASMA is the standards body for door and access systems, and UL Solutions publishes UL 325, the safety standard for automatic gate operators. If a contractor cannot tell you which standard a detail comes from, that is worth asking about before you sign.
Every welding & gate fabrication project in San Antonio gets the same attention, whether it is a single room or a full commercial job. We show up on schedule, keep the site clean, and stand behind the work — the estimate is free and there is no pressure.
Ready to get started? Call (877) 583-3964 for a free welding & gate fabrication free estimate in San Antonio, or request a quote and we'll get right back to you.