San Antonio Gate Pros provides professional swing gates in San Antonio, TX for residential and commercial properties across the San Antonio area. On limestone, a swing gate wins on arithmetic before anyone discusses looks. It needs two foundations. A cantilever needs three or four and a slide track needs a poured run. When each hole is cut out of rock rather than dug, the count of holes is the budget.
That is the single most useful thing we can tell a San Antonio homeowner who has been quoted three different gate types. Ask each bidder how many foundations their design requires and what the rock allowance is per hole. The design with the fewest cut foundations is very often the cheapest good gate, and on the majority of driveways here that is a pair of swing leaves. It is the question most bidders hope you do not ask.
Rock also rewards you once the holes are in. A hinge post grouted into sound limestone is anchored into material that does not care about moisture, and it holds its plumb essentially forever. Swing gates set that way keep their adjustment for years, which is why our service calls out here are usually about hardware and electronics rather than geometry. Ask for the test hole results too, not just the price.
Grade is the real design constraint. Driveways off the Hill Country side often rise from the street, and a gate that swings uphill has to clear the highest point in its arc rather than the point where it sits closed. We measure the arc before fabrication, and where the rise is steep we use rising-butt hinges or reverse the swing direction rather than cutting the bottom rail into a wedge.
One thing we steer people away from is underground swing operators. They look clean and they require a drained pit at each hinge post, which on rock means excavating two boxes instead of two cylinders. Above-ground arm and ram operators do the same job for a fraction of the excavation, and they are far easier to service. Serviceability is a real cost and it belongs in the comparison.
Grout is the part of a rock socket that most quotes leave vague. A non-shrink structural grout poured into a clean annulus transfers the post load into the surrounding stone; sand mix or dry concrete tipped down the gap does not, and it is the failure we are called out to most often on gates other people set. Ask what product goes in the hole and how the hole gets cleaned first.
Hardware is where we do not economize. Sealed ball-bearing hinges on a heavy leaf outlast pin-and-strap by many years and keep the operator from ever working hard. Latching hardware gets the same treatment, because a gate that will not catch reliably is a gate somebody eventually leaves open. Where a drop rod is needed we set the receiver into its own anchored socket rather than a hole punched in the driveway.
With 15+ years of experience, our insured team brings the right materials and equipment to every job — wrought iron and ornamental steel fabrication, ranch entry gates and pipe fencing, truck-rated cantilever slide gates, LiftMaster, DoorKing and FAAC operators, Class I-IV operator classifications, UL 325 entrapment protection — and backs the work with a written workmanship warranty. We serve San Antonio and nearby communities including Alamo Heights, Schertz, Converse, Universal City.
What We Handle
Everything our swing gates in San Antonio covers
One crew, one point of contact, and the full range of swing gates work in San Antonio, TX. If it is on this list we do it in house rather than handing it to a subcontractor:
- swing driveway gates
- single swing gates
- dual swing gates
- swing gate operators
- articulated arm gate openers
- underground swing gate operators
- dragging swing gate repair
- swing gate hinge replacement
- swing gate post setting
- rising hinge geometry for slopes
- swing gate leaf re-hanging
Not sure which one describes your situation? Describe it in plain words and we will sort it out — or browse the rest of our San Antonio services.
Materials, equipment and how we do swing gates
The difference between swing gates that lasts and swing gates that gets redone in three years is almost always preparation and materials, not the finish you see on day one. We work with wrought iron and ornamental steel fabrication, ranch entry gates and pipe fencing, truck-rated cantilever slide gates, LiftMaster, DoorKing and FAAC operators, spec them to the job instead of to the invoice, and write the material grades into the free estimate so you know exactly what you are buying.
Every San Antonio job runs the same way: site walk and measurements, written scope and fixed price, protection of the surrounding area, then the work itself with a daily clean-up. 15+ years of gate work in the San Antonio area means we have already met whatever your property is going to throw at us — awkward access, older construction, an HOA with opinions.
Where we do swing gates outside San Antonio
San Antonio Gate Pros covers San Antonio and the surrounding communities of the San Antonio area. Crews run out to the same nearby cities every week, so an out-of-town job does not mean an out-of-town price.
- Swing Gates in Alamo Heights, TX — Bexar County, population 8,400
- Swing Gates in Schertz, TX — Guadalupe, Comal and Bexar Counties, population 45,000
- Swing Gates in Converse, TX — Bexar County, population 28,000
- Swing Gates in Universal City, TX — Bexar County, population 20,000
- Swing Gates in Boerne, TX — Kendall County, population 20,000
- Swing Gates in Helotes, TX — Bexar County, population 10,000
Start on the San Antonio Gate Pros homepage for a free estimate, or call (877) 583-3964 and describe the job.
Why San Antonio Chooses San Antonio Gate Pros
- ✓Over 15 years installing and servicing gates across Bexar County and the Hill Country
- ✓In-house metal shop — we weld and powder coat our own gates rather than reselling panels
- ✓Footings sized to your actual soil, clay on the south side or limestone north of 1604
- ✓Every operator wired to UL 325 with photo eyes, loop detectors and tested entrapment protection
The standards behind swing gates
Quality here is not a matter of opinion — it is written down. The swing gates work we do in San Antonio follows published industry standards: DASMA is the standards body for door and access systems, and UL Solutions publishes UL 325, the safety standard for automatic gate operators. If a contractor cannot tell you which standard a detail comes from, that is worth asking about before you sign.
Every swing gates project in San Antonio gets the same attention, whether it is a single room or a full commercial job. We show up on schedule, keep the site clean, and stand behind the work — the estimate is free and there is no pressure.
Ready to get started? Call (877) 583-3964 for a free swing gates free estimate in San Antonio, or request a quote and we'll get right back to you.