San Antonio Gate Pros provides professional sliding gates in San Antonio, TX for residential and commercial properties across the San Antonio area. Slide gates suit driveways with no room to swing, a wall close to the opening, or a street where a swinging leaf would reach into traffic. There are two ways to build one, and in San Antonio the choice usually comes down to what concrete already exists on your property.
A V-track gate rolls on wheels riding a steel track fastened to concrete, which sounds like the expensive option on rock and often is not. If your slab already runs past the opening for the full length the gate must travel, the track bolts to concrete that is already there. No trenching, no coring, no rock saw. On commercial aprons and wide residential slabs that makes V-track the cheapest automated slide gate available here.
Where there is no existing concrete, the picture flips hard. A new track needs a continuous strip poured the full open length of the gate, and forming that strip on limestone means cutting a trench through rock for the whole run rather than digging one. That is a large number, and it is the point at which cantilever becomes the better value even though its own posts cost more to set.
So we walk the drive and measure before recommending anything. Runback distance, existing slab edges, where the rock comes up, and how much concrete you would be buying either way. The answer genuinely differs between two neighbors. Neighbors two doors apart have had opposite recommendations from us for exactly this reason, and both were right. Bring us the property rather than a product name and the answer falls out of the survey.
When V-track is the call, we specify large-diameter wheels, a track profile that sheds grit rather than collecting it, and guide posts set on their own foundations. Caliche dust and rock chips will stop a slide gate faster than any electronic fault, so track cleaning goes on the maintenance list. Bottom rollers, guide bearings and track fasteners are all wear items and go on an inspection list rather than being replaced after they fail.
Existing concrete is worth measuring rather than eyeballing. We check that the slab runs the full travel length, that its edge is straight enough to fix a track to, and that it is thick enough to hold anchors, which on a residential apron means four inches of unreinforced concrete that spalls. Any of the three turns V-track back into the expensive option.
Automation gets sized to the real leaf weight and cycle count, not the cheapest unit that fits. Every slide install leaves with photo eyes, entrapment protection matched to its class, and reversal tested by hand in front of you. Sizing to real duty rather than to the cheapest unit that fits is the difference between a gate that runs for a decade and one that becomes a service contract. We show you the cycle count we used.
With 15+ years of experience, our insured team brings the right materials and equipment to every job — wrought iron and ornamental steel fabrication, ranch entry gates and pipe fencing, truck-rated cantilever slide gates, LiftMaster, DoorKing and FAAC operators, Class I-IV operator classifications, UL 325 entrapment protection — and backs the work with a written workmanship warranty. We serve San Antonio and nearby communities including Alamo Heights, Schertz, Converse, Universal City.
What We Handle
Everything our sliding gates in San Antonio covers
One crew, one point of contact, and the full range of sliding gates work in San Antonio, TX. If it is on this list we do it in house rather than handing it to a subcontractor:
- sliding driveway gates
- rolling gates
- V-track slide gates
- roller gate installation
- slide gate off track repair
- slide gate wheels and bearings
- slide gate operator installation
- slide gate track cleaning
- narrow driveway gates
- V-track cleaning and re-leveling
- slide gate frame straightening
Not sure which one describes your situation? Describe it in plain words and we will sort it out — or browse the rest of our San Antonio services.
Materials, equipment and how we do sliding gates
The difference between sliding gates that lasts and sliding gates that gets redone in three years is almost always preparation and materials, not the finish you see on day one. We work with wrought iron and ornamental steel fabrication, ranch entry gates and pipe fencing, truck-rated cantilever slide gates, LiftMaster, DoorKing and FAAC operators, spec them to the job instead of to the invoice, and write the material grades into the free estimate so you know exactly what you are buying.
Every San Antonio job runs the same way: site walk and measurements, written scope and fixed price, protection of the surrounding area, then the work itself with a daily clean-up. 15+ years of gate work in the San Antonio area means we have already met whatever your property is going to throw at us — awkward access, older construction, an HOA with opinions.
Where we do sliding gates outside San Antonio
San Antonio Gate Pros covers San Antonio and the surrounding communities of the San Antonio area. Crews run out to the same nearby cities every week, so an out-of-town job does not mean an out-of-town price.
- Sliding Gates in Alamo Heights, TX — Bexar County, population 8,400
- Sliding Gates in Schertz, TX — Guadalupe, Comal and Bexar Counties, population 45,000
- Sliding Gates in Converse, TX — Bexar County, population 28,000
- Sliding Gates in Universal City, TX — Bexar County, population 20,000
- Sliding Gates in Boerne, TX — Kendall County, population 20,000
- Sliding Gates in Helotes, TX — Bexar County, population 10,000
Start on the San Antonio Gate Pros homepage for a free estimate, or call (877) 583-3964 and describe the job.
Why San Antonio Chooses San Antonio Gate Pros
- ✓Over 15 years installing and servicing gates across Bexar County and the Hill Country
- ✓In-house metal shop — we weld and powder coat our own gates rather than reselling panels
- ✓Footings sized to your actual soil, clay on the south side or limestone north of 1604
- ✓Every operator wired to UL 325 with photo eyes, loop detectors and tested entrapment protection
The standards behind sliding gates
Quality here is not a matter of opinion — it is written down. The sliding gates work we do in San Antonio follows published industry standards: DASMA is the standards body for door and access systems, and UL Solutions publishes UL 325, the safety standard for automatic gate operators. If a contractor cannot tell you which standard a detail comes from, that is worth asking about before you sign.
Every sliding gates project in San Antonio gets the same attention, whether it is a single room or a full commercial job. We show up on schedule, keep the site clean, and stand behind the work — the estimate is free and there is no pressure.
Ready to get started? Call (877) 583-3964 for a free sliding gates free estimate in San Antonio, or request a quote and we'll get right back to you.